For overseas Machine specifications for small-sized electric injection molding machine MEt3 series (180-ton clamp capacity)

Information of machine specifications of MEt3 series with 180-ton clamp capacity

Machine specifications for small-sized electric injection molding machine MEt3 series (180 tons)
Model Units 180MEt III
Injection Injection system - In-line screw
Injection stroke mm 112 128 144 160 128 144 160 160 184 200
Screw diameter mm 28 32 36 40 32 36 40 46 40 46 50 55
Theoretical injection capacity cm3 69 103 147 201 103 147 201 266 201 306 393 475
Standard Injection unit - 3.5S - -
Injection rate cm3/s 92 121 153 188 - -
Max. injection speed mm/s 150 - -
Max. injection pressure MPa 274.5 235.4 191.1 156.8 - -
Max. injection holding pressure MPa 274.5 215.6 171.5 137.2 - -
High-speed Injection unit - 3.5H 7H 15H
Injection rate cm3/s 185 241 305 377 169 214 264 349 264 349 412 499
Max. injection speed mm/s 300 210 210
Max. injection pressure MPa 274.5 250.0 196.0 161.7 264.0 250.0 215.6 166.6 244.0 215.6 186.2 156.8
Max. injection holding pressure MPa 274.5 225.5 176.4 142.1 264.0 250.0 186.2 147.0 244.0 196.0 166.6 137.2
Superhigh speed Injection unit - - 7U 15U
Injection rate cm3/s - 322 407 503 665 377 499 589 713
Max. injection speed mm/s - 400 300
Max. injection pressure MPa - 264.0 250.0 215.6 166.6 244.0 215.6 186.2 156.8
Max. injection holding pressure MPa - 264.0 250.0 186.2 147.0 244.0 196.0 166.6 137.2
Recovery rate (PS) kg/h 41.0 62.0 89.0 113.0 62.0 89.0 113.0 172.0 97.0 157.0 200.0 227.0
Screw revolution speed min-1 350 300
Nozzle pressing force kN 24.5 24.5
Clamping Clamping system - Double toggle
Clamping force kN 1764
Clamping stroke mm 470
Min. mold height mm 200
Max. mold height mm 500[600]
Tie bar clearance (H×V) mm 560x560
Die plate size (H×V) mm 780x780
Ejector force kN 34.3
Ejector stroke mm 120
Other Heater capacity kW 5.50 5.85 6.50 7.95 5.85 6.50 7.95 11.20 7.95 11.20 13.50 16.70
Mold height motor output kW 0.2
Nozzle touch motor output kW 0.2
Machine dimension <L> mm 5158 5158 5160 5278 5158 5160 5278 5451 5410 5583 5653 5874
Machine dimensions <W×H> mm 1303x1750  
Power source - Three-phase AC200V/200, 220V±10% 50Hz/60Hz
Main breaker capacity A 175(7U,15U:225)
Total electric capacity KVA 3.5S:22 15H:43
3.5H:27 15U:58
7H:29
7U:49
Cable size
200V Class[400V Class *1]		 mm2 3.5S·3.5H·7H:38[22] 15H:38[22]
7U:60[22] 15U:60[22]
Machine weight t 7.1 7.4
NOTES
  1. The figures are subject to change without any legal obligation on the part of the manufacture.
  2. The specifications are expressed in SI.
    (1MPa=10.2kgf/cm2 1kN=0.102tonf)
  3. The maximum injecting pressure and the maximum holding pressure are attainable maximum set values. There values may be limited by molding conditions and cycle time.
  4. The injection rate and the maximum injecting speed are calculated values.
    These values may be limited by set injecting pressures.
  5. When a screw with wide diameter is used, some resins may not be accepted.
  6. When the machine is attached with an option, the capacity of the breaker.may be changed.
  7. The values in brackets are applied to machines with options.
    *1.A transformer(option) is necessary on the machine side.

Copyright(C) MITSUBISHI HEAVY INDUSTRIES PLASTIC TECHNOLOGY CO.,LTD. All Right Reserved.