For overseas Machine specifications for small-sized electric injection molding machine MEt3 series (230-ton clamp capacity)

Information of machine specifications of MEt3 series with 230-ton clamp capacity

Machine specifications for small-sized electric injection molding machine MEt series (230 tons)
Model Units 230MEt III
Injection Injection system - In-line screw
Injection stroke mm 128 144 160 160 184 200 200 220
Screw diameter mm 32 36 40 46 40 46 50 55 50 55 60
Theoretical injection capacity cm3 103 147 201 266 201 306 393 475 393 522 622
Standard Injection unit - - - -
Injection rate cm3/s - - -
Max. injection speed mm/s - - -
Max. injection pressure MPa - - -
Max. injection holding pressure MPa - - -
High-speed Injection unit - 7H 15H 20H
Injection rate cm3/s 169 214 264 349 264 349 412 499 393 475 565
Max. injection speed mm/s 210 210 200 200 200
Max. injection pressure MPa 264.0 250.0 215.6 166.6 244.0 215.6 186.2 156.8 235.0 196.0 166.6
Max. injection holding pressure MPa 264.0 250.0 186.2 147.0 244.0 196.0 166.6 137.2 215.6 176.4 147.0
Superhigh speed Injection unit - 7U 15U -
Injection rate cm3/s 322 407 503 665 377 499 589 713 - - -
Max. injection speed mm/s 400 300 -
Max. injection pressure MPa 264.0 250.0 215.6 166.6 244.0 215.6 186.2 156.8 - - -
Max. injection holding pressure MPa 264.0 250.0 186.2 147.0 244.0 196.0 166.6 137.2 - - -
Recovery rate (PS) kg/h 62.0 89.0 113.0 172.0 97.0 157.0 200.0 227.0 200.0 227.0 242.0
Screw revolution speed min-1 350 300 300
Nozzle pressing force kN 24.5 24.5 29.4
Clamping Clamping system - Double toggle
Clamping force kN 2254
Clamping stroke mm 550
Min. mold height mm 250
Max. mold height mm 580[680]
Tie bar clearance (H×V) mm 610x610
Die plate size (H×V) mm 820x820
Ejector force kN 51.9
Ejector stroke mm 150
Other Heater capacity kW 5.85 6.50 7.95 11.20 7.95 11.20 13.50 16.70 13.50 16.70 19.50
Mold height motor output kW 0.4
Nozzle touch motor output kW 0.2 0.4
Machine dimension <L> mm 5727 5783 5956 5915 6088 6158 6378 6199 6372 6544
Machine dimensions <W×H> mm 1393x1817
Power source - Three-phase AC200V/200, 220V±10% 50Hz/60Hz
Main breaker capacity A 200(7U,15U:225)
Total electric capacity KVA 7U:49 15H:43 52
7H:29 15U:58
Cable size
200V Class[400V Class *1]		 mm2 60[22]
Machine weight t 11 11.3 12.0
NOTES
  1. The figures are subject to change without any legal obligation on the part of the manufacture.
  2. The specifications are expressed in SI.
    (1MPa=10.2kgf/cm2 1kN=0.102tonf)
  3. The maximum injecting pressure and the maximum holding pressure are attainable maximum set values. There values may be limited by molding conditions and cycle time.
  4. The injection rate and the maximum injecting speed are calculated values.
    These values may be limited by set injecting pressures.
  5. When a screw with wide diameter is used, some resins may not be accepted.
  6. When the machine is attached with an option, the capacity of the breaker.may be changed.
  7. The values in brackets are applied to machines with options.
    *1.A transformer(option) is necessary on the machine side.

Copyright(C) MITSUBISHI HEAVY INDUSTRIES PLASTIC TECHNOLOGY CO.,LTD. All Right Reserved.