Machine specifications for small-sized electric injection molding machine MEt3 series (50-ton clamp capacity)

Information of machine specifications of MEt3 series with 50-ton clamp capacity

Machine specifications for small-sized electric injection molding machine MEt3 series (50 tons)
Model Units 50MEt III
Injection Injection system - In-line screw
Injection stroke mm 64 72 72 96 112
Screw diameter mm 16 18 20 20 24 28 32
Theoretical injection capacity cm3 13 18 23 23 43 69 90
Standard Injection unit - - 1.5H
Injection rate cm3/s - 94 136 185 -
Max. injection speed mm/s - 300
Max. injection pressure MPa - 274.5 235.4 182.3 -
Max. injection holding pressure MPa - 274.5 196.0 147.0 -
High-speed Injection unit - 0.7H 2.5H
Injection rate cm3/s 60 76 94 - 136 185 241
Max. injection speed mm/s 300 300
Max. injection pressure MPa 254.9 254.9 235.2 - 274.5 235.2 181.3
Max. injection holding pressure MPa 254.9 254.9 235.2 - 274.5 176.4 147.0

Superhigh speed

 Injection unit - 0.7U 2.5U
Injection rate cm3/s 101 127 157 - 226 308 402
Max. injection speed mm/s 500 500
Max. injection pressure MPa 254.9 254.9 235.2 - 274.5 235.2 181.3
Max. injection holding pressure MPa 254.9 254.9 235.2 - 274.5 176.4 147.0
Recovery rate (PS) kg / h 11.1 14.4 17.6 13.9 25.0 41.0 62.0
Screw revolution speed min-1 500 350
Nozzle pressing force kN 9.8 19.6
Clamping Clamping system - Double toggle
Clamping force kN 490
Clamping stroke mm 270
Min. mold height mm 150
Max. mold height mm 380
Tie bar clearance (H×V) mm 360x325
Die plate size (H×V) mm 500x460
Ejector force kN 19.2
Ejector stroke mm 70
Other Heater capacity kW 2.05 2.275 2.575 3.45 5.50 5.50 5.85
Mold height motor output kW 0.1
Nozzle touch motor output kW 0.1 0.2
Machine dimension <L> mm 3427 3427 3494 3590 3692
Machine dimensions <W×H> mm 1001x1523
Power source - Three-phase AC200V/200, 220V±10% 50Hz/60Hz
Main breaker capacity A 75(2.5U:150)
Total electric capacity KVA 0.7H:10 1.5H:13
0.7U:18 2.5H:20
  2.5U:35
Cable size
200V Class[400V Class *1]		 mm2 14[8] 2.5H:14[8]
2.5U:38[14]
Machine weight t 2.0 2.2
NOTES
  1. The figures are subject to change without any legal obligation on the part of the manufacture.
  2. The specifications are expressed in SI.
    (1MPa=10.2kgf/cm2 1kN=0.102tonf)
  3. The maximum injecting pressure and the maximum holding pressure are attainable maximum set values. There values may be limited by molding conditions and cycle time.
  4. The injection rate and the maximum injecting speed are calculated values.
    These values may be limited by set injecting pressures.
  5. When a screw with wide diameter is used, some resins may not be accepted.
  6. When the machine is attached with an option, the capacity of the breaker.may be changed.
  7. The values in brackets are applied to machines with options.
    *1.A transformer(option) is necessary on the machine side.

Copyright(C) MITSUBISHI HEAVY INDUSTRIES PLASTIC TECHNOLOGY CO.,LTD. All Right Reserved.